NEW ACCOUNTS      FORGOT PASSWORD      CONTACT US      GIFT CERTIFICATES     

Lee Precision Carbide 3-Die Set .500 Smith & Wesson Magnum

Lee Precision Carbide .500 Smith & Wesson Magnum 3-Die Pistol Set uses a solid carbide insert ground to a special contour that does not leave the objectionable belt mark on the cases, common to the ordinary carbide dies. A Carbide Full Length Sizing Die is a must if you are reloading for more than one firearm or reloading cases that were fired in other firearms. No case lube is needed, and you don't have to clean your cases.

Taper crimp dies are used to correct problems caused by the improper expanding plug design or adjustment. They distort the bullet shank and reduce accuracy. The Powder Thru Expanding Die charges the case while expanding the mouth. All of the flare is removed with the Bullet Seating Die. Thus eliminating the need for a tapered crimp die.

Includes:

  • Carbide Full Length Sizing Die (shown in image at the right)Lee Precision Carbide Sizing Die Cutaway
  • Bullet Seating Die
  • Powder Thru Expanding Die
  • Universal Shell Holder
  • Powder Dipper
  • Instructions
  • Load Data

NOTES:

IT IS YOUR RESPONSIBILITY TO ENSURE THE SAFETY OF YOUR LOADS

FACTORS THAT WILL INCREASE PRESSURES. SOME WILL BE DANGEROUS:

  • DO NOT USE more powder than recommended
  • DO NOT USE a heavier bullet than recommended
  • DO NOT SEAT the bullet deeper than normal
  • DO NOT USE magnum primers unless using a slow burning ball powder
  • Greatly oversize bullets, excessively hard bullets or cases that are too long will cause higher pressures
  • High temperatures or cartridges that were stored in a hot car or trunk will produce higher pressures

WARNING:

Ammunition reloading can be dangerous if done improperly, and should not be attempted by persons not willing and able to read and follow the instructions included with each product exactly.

  • Always wear safety glasses when reloading and shooting.
  • Ammunition loaded with these tools should be used in modern guns, in good condition.
  • Children should not be permitted to reload ammunition without strict parental supervision.
  • Primers and gun powders, like gasoline and matches, can be dangerous if improperly handled or misused.
  • We do not accept responsibility for ammunition loaded with these tools, as we have no control over the manufacture and storage of components or the loading procedure and techniques used.
Help for product 90288
Parts Manual

Product WARNINGS:

We are required to provide Prop 65 product warnings by California's Dear Leader. Please give them appropriate attention.


 

Prop 65: Warning: Handling live primers and spent primers may expose you to lead or other chemicals, which are known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

Prop 65: Warning: This product may contain steel alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov. To prevent exposure, do not alter the product by welding, grinding, etc.

Write a review

Logged in customers receive 20 reward points for posting a valid product review. See the Customer Rewards Program for details.
Note: HTML is not translated!
    Bad           Good

Lee Precision Carbide 3-Die Set .500 Smith & Wesson Magnum

Brand: Lee Precision
Product Code: 90288
Reward Points: 40
Only Ships to: Selected Countries
Availability: Only 1 Left! Don't miss it!

MSRP: $56.98
MPN: 90288
Material: Steel
Condition: new
Country of Origin: United States
Package Quantity: 3 Dies
UPC: 7343079028890
Shipping Restrictions: No
Carrier Restrictions: No
DOT Regulated: No
Calibers: .500 Smith & Wesson Magnum
Language: Engllish

  • $39.99

  • Price in reward points: 2400
Help for product 90288
Parts Manual

Related Products

Lee Precision Auto Prime Shell Holder #16

Lee Precision Auto Prime Shell Holder #16

The Lee Precision Shell Holder #16 fits .500 S&W Magnum, 12.7x41mmSR, 7.62x54mmR, 7.62x54 Russia..

Read more...

$3.34 $3.99

Lee Precision Bullet Seat Plug 500 S&W

Lee Precision Bullet Seat Plug 500 S&W

This is a repair part for Lee Precision reloading tools. The product photos show a typical repair pa..

Read more...

$1.99

Lee Precision Charge Table 500 S&W

Lee Precision Charge Table 500 S&W

This is a repair part for Lee Precision reloading tools. The product photos show a typical repair pa..

Read more...

$3.99

Lee Precision Shell Holder R16 (.500 S&W, 7.62x54mm)

Lee Precision Shell Holder R16 (.500 S&W, 7.62x54mm)

The Lee Precision R16 Universal Shell Holder fits .500 S&W Magnum, 12.7x41mmSR, 7.62x54mmR, 7.62..

Read more...

$4.01 $4.79

Lee Precision Case Length Gauge & Shell Holder .500 Smith & Wesson

Lee Precision Case Length Gauge & Shell Holder .500 Smith & Wesson

This Lee Precision Case Length Gauge is the easiest way to trim .500 S&W cases to the proper length ..

Read more...

$5.30 $6.29

Lee Precision Quick Trim Die .500 Smith & Wesson

Lee Precision Quick Trim Die .500 Smith & Wesson

The Lee Precision .500 Smith & Wesson Quick TrimPistol Die is used in conjunction with..

Read more...

$11.29

Lee Precision Breech Lock Pro Shell Plate 16

Lee Precision Breech Lock Pro Shell Plate 16

FITS:.500 Smith & Wesson7.62x54mmRNOTES:These cartridges are too large to work with the Lee Univ..

Read more...

$16.24 $18.99

Lyman Premium Carbide 3-Die Set 500 S&W

Lyman Premium Carbide 3-Die Set 500 S&W

Lyman was the originator of the Tungsten Carbide (T-C) sizing die and "Multi" concept with the addit..

Read more...

$65.99

MTM Case-Gard Hinge Top Ammo Box 50 Rounds 223 WSSM, 243 WSSM, 500 S&W Magnum

MTM Case-Gard Hinge Top Ammo Box 50 Rounds 223 WSSM, 243 WSSM, 500 S&W Magnum

These are the newer CASE-GARD ammo boxes. Made of virtually indestructible polypropylene that will n..

Read more...

$3.40 $3.99

RCBS Carbide 3-Die Set 500 S&W

RCBS Carbide 3-Die Set 500 S&W

RCBS(R) pioneered and developed 3-Die Sets for straight-wall rifle and pistol cases. The Carbide Siz..

Read more...

$99.99

Tags: rcbs, carbide, 3-die, set, , for, 500, s&w, 23812, reloading, equipment s&w, rc-23812 s&w s&w s&w s&w

Also Bought

Lee Precision Collet Style Crimp Die .500 S&W

The Lee Precision Factory Crimp Die. Incorporates a collet to apply a rifle type crimp to the case. ..

Read more...

$10.06 $11.49

Lee Precision Case Length Gauge & Shell Holder .500 Smith & Wesson

This Lee Precision Case Length Gauge is the easiest way to trim .500 S&W cases to the proper length ..

Read more...

$5.30 $6.29

Lee Precision Auto Prime Shell Holder #16

The Lee Precision Shell Holder #16 fits .500 S&W Magnum, 12.7x41mmSR, 7.62x54mmR, 7.62x54 Russia..

Read more...

$3.34 $3.99

Lee Precision Die Box Round Red

The Lee Precision Red Round Die Box, the perfect storage for your dies. Round box made of durab..

Read more...

$7.49