NEW ACCOUNTS      FORGOT PASSWORD      CONTACT US      GIFT CERTIFICATES     

Lee Precision Mold Double Cavity TL410-210-SWC

This Lee Precision Double Cavity Bullet Mold produces .410 diameter 210 grain Semi Wad Cutter nose bullets suitable for .41 Magnum. This mold, like all Lee Precision molds, is made from aluminum and so is completely rust resistant, lighter, and heats up and cools down faster than other brands made from iron or steel. Handles included.

As a result, this Lee mold is easier to use, causes less operator fatigue during casting and can produce more consistent bullets than other molds made from iron or steel. Lee's mold blocks are machined from aluminum and assembled with steel bushings and alignment pins for lasting precision.

WARNING: Melting lead and casting lead objects will expose you and others in the area to lead which is known to cause birth defects, other reproductive harm and cancer. See instructions on Reducing Exposure supplied with product.

This Lee Precision Double Cavity Bullet Mold produces .410 diameter 210 grain Semi Wad Cutter nose bullets suitable for .41 Magnum. This mold, like all Lee Precision molds, is made from aluminum and so is completely rust resistant, lighter, and heats up and cools down faster than other brands made from iron or steel. As a result, Lee molds are easier to use, cause less operator fatigue during casting and can produce more consistent bullets than other brands made from iron or steel. Lee's mold blocks are CNC machined to provide unmatched precision.

Handles and sprue plate are included. The bullet weight specified is based on using Lee's suggested alloy, your results may vary depending on the actual alloy used.

INCLUDES:

  • Hardwood handles
  • Hard anodized sprue plate
  • Two Aluminum mold block halves

FEATURES:

  • Produces a bullet that fits .41 Magnum.
  • Bullet diameter: .410 inches
  • Bullet weight: 210 grains (with Lee's suggested alloy)
  • Bullet overall length: .N/A
  • Distance from nose to first lube groove: N/A
  • Bullet shape: Semi Wad Cutter nose
  • Ballistic Coefficient: N/A
  • 2 bullets are produced with each casting.
  • Mold block halves are CNC machined from aluminum for exacting precision.
  • A tangential cutoff helps reduce the nip at cutoff.

NOTES:

Lead Information:

  • The following lead information is from the Lee Precision Modern Reloading 2nd Edition Book, Pages 119 & 120.
  • For best results, bullet strength must be matched to breech pressure.
  • Black Powder guns require Pure Lead.
  • Target handgun loads should use Lead with 1% Tin. Tin makes bullet alloy more castable & harder.
  • Lead with some wheel weights used for high pressure handguns.
  • Use Wheel Weights for very light rifle loads.
  • High Pressure Rifle loads use Linotype.
  • Beware of Zinc! One part Zinc in 10,000 parts of Lead Alloy will ruin it's castability.

WARNING: Melting lead and casting lead objects will expose you and others in the area to lead which is known to cause birth defects, other reproductive harm and cancer.

USE STRONG VENTILATION

Lead contamination in the air, dust and on your skin is invisible. Keep Children and pregnant women away during use and until clean-up is complete. Risk can be reduced, BUT NOT eliminated , with strong ventilation. Washing hands immediately after use of these products before eating or smoking. Careful cleaning of surfaces and floors with disposable wipes, after lead dust has settled. Use lead-specific cleaner with EDTA or high phosphate detergent (such as dishwasher detergent). Bag wipes for disposal.

IT IS YOUR RESPONSIBILITY TO ENSURE THE SAFETY OF YOUR LOADS

FACTORS THAT WILL INCREASE PRESSURES. SOME WILL BE DANGEROUS:

  • DO NOT USE more powder than recommended
  • DO NOT USE a heavier bullet than recommended
  • DO NOT SEAT the bullet deeper than normal
  • DO NOT USE magnum primers unless using a slow burning ball powder
  • Greatly oversize bullets, excessively hard bullets or cases that are too long will cause higher pressures
  • High temperatures or cartridges that were stored in a hot car or trunk will produce higher pressures

WARNING:

Ammunition reloading can be dangerous if done improperly, and should not be attempted by persons not willing and able to read and follow the instructions included with each product exactly.

  • Always wear safety glasses when reloading and shooting.
  • Ammunition loaded with these tools should be used in modern guns, in good condition.
  • Children should not be permitted to reload ammunition without strict parental supervision.
  • Primers and gun powders, like gasoline and matches, can be dangerous if improperly handled or misused.
  • We do not accept responsibility for ammunition loaded with these tools, as we have no control over the manufacture and storage of components or the loading procedure and techniques used.

Help for product 90335
Parts Manual Video

Product WARNINGS:

We are required to provide Prop 65 product warnings by California's Dear Leader. Please give them appropriate attention.


Prop 65: Warning: for the melters and bullet molds: WARNING: Melting and casting lead objects will expose you and others in the area to lead, which is known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov. See instructions on Reducing Exposure supplied with product.

Write a review

Logged in customers receive 20 reward points for posting a valid product review. See the Customer Rewards Program for details.
Note: HTML is not translated!
    Bad           Good

Lee Precision Mold Double Cavity TL410-210-SWC

Brand: Lee Precision
Product Code: 90335
Reward Points: 33
Only Ships to: Selected Countries
Availability: Out Of Stock - No Backorder

MSRP: 44.98
MPN: 90335
Material: Aluminum/Steel/Wood
Color: Aluminum/Black/Wood
Condition: new
Country of Origin: United States
Package Quantity: 1
Product Weight: 0.9 lbs
UPC: 7343079033504
Shipping Restrictions: No
Carrier Restrictions: No
DOT Regulated: No
Calibers: 40 S&W 10mm etc.
Bullet Type: SemiWad Cutter, Micro Band Grove
Bullet Weight: 210 grain
Bullet Length: .658 inches
Bullet Diameter: .410 inches
Nose to Driving Ring: .283 inches

  • $32.69

  • Price in reward points: 1962
Help for product 90335
Parts Manual Video

Related Products

Lee Precision Mold Single Cavity 575-500-M

Lee Precision Mold Single Cavity 575-500-M

The Lee Precision Single Minie Bullet Mold produces a .575 diameter 500 grain Minie bullet (origin..

Read more...

$42.89

Lee Precision Mold Double Cavity 429-214-SWC

Lee Precision Mold Double Cavity 429-214-SWC

This Lee Precision Double Cavity Bullet Mold produces .429 diameter 214 grain Semi Wad Cutter nose ..

Read more...

$32.69

Lee Precision Mold Double Cavity 410-195-SWC

Lee Precision Mold Double Cavity 410-195-SWC

This Lee Precision Double Cavity Bullet Mold produces .410 diameter 195 grain Semi Wad Cutter nose ..

Read more...

$35.89

Lee Precision Mold Double Cavity TL358-158-SWC

Lee Precision Mold Double Cavity TL358-158-SWC

This Lee Precision Double Cavity Bullet Mold produces .358 diameter, 150 grain Semi Wad round nose ..

Read more...

$32.69

Lee Precision Mold Double Cavity 358-150-1R

Lee Precision Mold Double Cavity 358-150-1R

This Lee Precision Double Cavity Bullet Mold produces .358 diameter, 150 grain Semi Wad round nose ..

Read more...

$32.69

Tags: lee, precision, mold, double, cavity, 358-150-1r, .38, special, s&w, colt, new, police, .357, mag

Also Bought

Lee Precision Commercial Mold Handles

Lee Precision Commercial Mold Handles fits Lee 6-Cavity Molds, also most other brands of single & do..

Read more...

$24.99

Lee Precision Under-Size Mandrel .260

When delivered from the factory, the collet die will grip the bullet with a light press fit with cas..

Read more...

$4.99

Lee Precision Ingot Mold

Lee Precision Ingot Mold, made of rustproof aluminum mold casts 1/2 and 1 lb. ingots (2 of each). Pe..

Read more...

$19.09

Lee Precision Adjustable Shot Dipper

The Lee Precision Adjustable Shot Dipper accurately measures lead, bismuth and steel. Works great fo..

Read more...

$3.89